- #Dllkit pro v1.0.0.5 code install
- #Dllkit pro v1.0.0.5 code manual
- #Dllkit pro v1.0.0.5 code code
- #Dllkit pro v1.0.0.5 code download
- #Dllkit pro v1.0.0.5 code windows
2 nd - make sure you have the M420 S1 command AFTER the G28 line in your print initialization GCode.1 st - make sure you manually leveled the bed, the probing tends to fail if any part of the bed is >2mm lower or higher than the home level.Don't forget to save the settings after the print to keep the offset in the memory, you can use the LCD or the M500 GCode for this. The nozzle will always be far from the bed until you adjust the offset to a negative value ( LCD -> Prepare -> Bed Leveling -> Z Offset). After enabling the bed level, print something large and flat to adjust the Z offset.
#Dllkit pro v1.0.0.5 code code
Add the following gcode to the startup code of you slicer, right after the line of the G28 command to load the bed level configuration from the memory before every print:. Save the settings using the LCD menu or the M500 gcode (if you used the Heat and Level custom command, they will be automatically saved). Note that the Heat and Level command waits 2 minutes after the bed is hot to allow the mounted surfaces to expand/contract properly. Heat the bed to the printing temperature and run the bed level command from the LCD ( Prepare -> Bed Leveling -> Level bed) or using the G29 gcode or using the Heat and Level command from the custom menu (recommended). The card thickness does not matter because the BLTouch probe will redefine the Z reference. #Dllkit pro v1.0.0.5 code manual
This is what you would do in manual calibration but instead of using a paper you will use the card for convenience. For each position, adjust the bed level knobs to keep the nozzle at the credit card thickness distance from the nozzle.
Move hot end to several positions of the bed, starting from the 4 corners. Turn the Z axis with your hand until the nozzle hits the credit card. Place a credit card on one the bed, the thickness of the card will be used as a reference distance. Disable stepper motors using the LCD menu command. Heating should have little to no effect on this specific procedure. Manually pre-level the bed! This is important because the BLTouch has limited max/min detection ranges and the print quality can be affected if the Z-Axis moves too much. If everything goes well another message like this "= 1 succeeded in 0055.010 =" will be printed. Go to the Visual Code menu Terminal->Run Task->Upload. Connect your printer to the computer using the USB cable. If the code compiled properly you will see something like this in the terminal: "= 1 succeeded in 0030.050 =". #Dllkit pro v1.0.0.5 code download
It will take a few minutes for the system to download all dependencies and compile the code.
Save the file and then select Terminal->Run Task->Build. This offset may need to be measured manually with a caliper, only use this as a starting point. # define NOZZLE_TO_PROBE_OFFSET (Found from Creality config here: ) The default settings X = -42mm, Y= -5mm and Z=0 are for this mount: This does not need to be too precise, the only purpose is avoiding the probe to test outside the bed. Look for the configuration.h inside the "Marlin" sub-folder and edit the following configuration to the relative coordinates of your BLTouch mount to the Nozzle. Attention! Use the "open folder" command, not the"open file". From Visual Studio Code select File->Open folder and select the folder where the platformio.ini file is located. With all requirements running, unpack the entire Marlin source code downloaded from the link below to a folder. #Dllkit pro v1.0.0.5 code install
From Visual Studio Code extension menu, install the PlatformIO IDE extension. Download and install Visual Studio Code. If you want to do quick/imprecise bed leveling before every print you will need to reconfigure the firmware. This firmware configuration reflects this choice. 
Based on my experience with the Ender 3, it's better to do an extremely precise (slower) bed leveling when necessary than a simpler one before every print. There are two ways to perform the automatic bed leveling, the first is before every print and the second is only when necessary.
#Dllkit pro v1.0.0.5 code windows
AVRDude for installation option 3 in Linux or MacOS (AVRDude for Windows is included in the package). Visual Studio Code for installation option 2. There are different BLTouch sensors and the YouTube videos tips are most of the times wrong IMPORTANT! BLTouch tip height must be adjusted according to the official instruction manuals. Z stop switch removed (it can block the Z axis movement). 
The kit used to configure this around was the Creality BLTouch kit and mount that was supplied within it.ĭownload the modified firmware folder here: Requirements We have uploaded a modified firmware for Ender 5 & Ender 5 Pro which is the latest version of Marlin 1.1.9 from the marlin website, and modified the configuration for Ender 5 printers as well as BLTouch options enabled.
0 kommentar(er)
